Galfab

Galfab, Extendible Tail Hoist (EX Series)

Condition: Build to Order

Make: Galfab

Partners: Galfab, Municipal Equipment, Inc., SWAT (Solid Waste Applied Technologies)

The Extendible Tail Hoist (EX Series) has a sliding tail that provides operators the option of loading in areas with low overhead clearance. Galfab offers this hoist with an 8” mainframe and 2” subframe or the very popular 10” sub frameless hoist. Available in 60k and 75k pound models to fit any application.

8″ x 4 x 3/8” Main Frame Tube
½ inch x 3 ½ inch Wear Strip on Top
3″ x 2″ x 1/4″ Sub Frame
2 1/2″ Diameter Rear Hinge
All Working Points Greaseable
Pintle Ready Apron
1″ Spring Loaded Container Locks
2 1/2″ Diameter Lift Cylinder Shafts
Interchangeable 10″ Vertical and Horizontal Sheaves
3/8 inch x 3 inch Winch Cylinder Rod Covers
6 Inboard and Outboard Supported Outside Rollers
48 Gallon Oil Reservoir with Sight and Temperature Gauge
25 Micron Filtration
Inside and Outside Controls
Choice of Forward or Reverse Mount Single Stage or Telescopic Lift Cylinders
LED Lighting System
7/8” Cable with Heavy Duty Swivel Eye Hook
80 inch Extendible Tail
No DOT bumper
Front Mount Pump
Hoist Up Warning Light
Sealed Wiring System
Hoist Up Alarm
Backup Alarm

Behind Cab and Oversize Oil Tanks
Tool Boxes
Auxiliary Stops
Poly or Steel Fenders
Aluminum Fenders
Tarping Systems
Hooker Hold On Systems
Ratchet Tie Down Straps
PTO
Drop Shaft
Integrated hydraulics can be used, if hydraulic tarping system is used
Rear View Camera Systems
Work Lights
Onboard Scale Systems

Model	Capacity	CA	CA with tarp	Length	Dump Angle Tail Retracted	Load Angle Tail Extended	Up (sec)*	Down (sec)*	On (sec)*	Off (sec)*	Lift Cylinder	Winch Cylinder	Container Length ft	Apx Weight lbs
EX60174S072	60,000	174″	186″	19′ 10″	48°	27°	27	15	41	28	6″ x 4″ x 72″ DA	7″ x 4″ x 79.5″ DA	18′-22′	7550
EX60174S072R	60,000	174″	186″	19′ 10″	48°	27°	27	15	41	28	6″ x 4″ x 72″ DA	7″ x 4″ x 79.5″ DA	18′-22′	7550
EX60174T121	60,000	174″	186″	19′ 10″	48°	27°	35	29	41	28	6″-5″-4″ x 121″ DAT	7″ x 4″ x 79.5″ DA	18′-22′	7225
EX75174S072F7	75,000	174″	186″	19′ 10″	48°	27°	37	23	41	28	7″ x 4″ x 72″ DA	7″ x 4″ x 79.5″ DA	18′-22′	7550
EX75174S072R7	75,000	174″	186″	19′ 10″	48°	27°	37	23	41	28	7″ x 4″ x 72″ DA	7″ x 4″ x 79.5″ DA	18′-22′	7550
EX75174T121	75,000	174″	186″	19′ 10″	48°	27°	35	29	41	28	6″-5″-4″ x 121″ DAT	7″ x 4″ x 79.5″ DA	18′-22′	7350
EX60194S072	60,000	194″	206″	21′ 5″	48°	27°	27	15	46	31	6″ x 4″ x 72″ DA	7″ x 4″ x 89.5″ DA	20′-24′	7850
EX60194S072R	60,000	194″	206″	21′ 5″	48°	27°	27	15	46	31	6″ x 4″ x 72″ DA	7″ x 4″ x 89.5″ DA	20′-24′	7850
EX60194T121	60,000	194″	206″	21′ 5″	48°	27°	35	29	46	31	6″-5″-4″ x 121″ DAT	7″ x 4″ x 89.5″ DA	20′-24′	8075
EX75194S072F7	75,000	194″	206″	21′ 5″	48°	27°	37	23	46	31	7″ x 4″ x 72″ DA	7″ x 4″ x 89.5″ DA	20′-24′	7850
EX75194S072R7	75,000	194″	206″	21′ 5″	48°	27°	37	23	46	31	7″ x 4″ x 72″ DA	7″ x 4″ x 89.5″ DA	20′-24′	7850
EX75194T121	75,000	194″	206″	21′ 5″	48°	27°	35	29	46	31	6″-5″-4″ x 121″ DAT	7″ x 4″ x 89.5″ DA	20′-24′	8075

* Cycle Times are Factory developed and controlled by PTO output, oil viscosity, human and mechanical efficiency, and may vary accordingly.

CAUTION: This Equipment Should be Operated by Properly Trained Personnel. Improper Use, Misuse, or Lack of Maintenance Could Cause Injury to Persons or Property. Photos used in this brochure are illustrative only. We reserve the right to make changes at any time without notice. Information contained within this literature is believed to be the most accurate available at the time of printing.

Please contact one of the EMP Partner(s) below: